SL:Introduction: Unterschied zwischen den Versionen

Aus Doc-Wiki
Zur Navigation springen Zur Suche springen
imported>Burghardt
(Die Seite wurde neu angelegt: „Sensorlab introduction...“)
 
imported>Burghardt
Zeile 1: Zeile 1:
  +
−
Sensorlab introduction...
  
  +
  +
== Nodes Hardware ==
  +
  +
The sensor nodes we have ordered are from Crossbow technology (http://www.xbow.com/Products/productdetails.aspx?sid=264)
  +
Basically, the sensors operate in 2.4GHz ISM band. The range of the radio module is about up to 50 m indoor and up to 300 m outdoor.
  +
  +
For more details see the data sheet: http://www.xbow.com/Products/Product_pdf_files/Wireless_pdf/IRIS_Datasheet.pdf
  +
  +
Sensor board: MTS400 including the following sensors
  +
* Dual-axis Accelerometer: Analog Devices ADXL202JE
  +
* Barometric Pressure Sensor: Intersema MS5534AM
  +
* Ambient Light Sensor: TAOS TSL2550D
  +
* Relative Humidity & Temperature Sensor: Sensirion SHT11
  +
  +
== Documents ==
  +
=== TinyOS ===
  +
General documents can be found on http://docs.tinyos.net/index.php/Main_Page
  +
  +
TinyOS Iris API: http://www.tinyos.net/tinyos-2.1.0/doc/nesdoc/iris/
  +
  +
=== How To ===
  +
[[Media:20100107_How_to_disassemble_a_sensor_node_to_reprogramme_it.pdf|How To Disassemble a Sensor Node to Reprogram it (.pdf)]] [[Media:20100107_How_to_disassemble_a_sensor_node_to_reprogramme_it.doc|(.doc)]]
  +
  +
=== Modifications for iris motes ===
  +
==== PacketParrot application ====
  +
The PacketParrot application which is provided with TinyOS does not work on directly on the Iris motes. Thus, the following modified version can be used instead. The modifications are basically replacing the special radio component, which is used for sending and receiving, by the generic AMSenderC and AMReceiverC components.
  +
  +
[[Media:PacketParrotC.nc| PacketParrotC.nc]]
  +
  +
[[Media:PacketParrotP.nc| PacketParrotP.nc]]
  +
  +
== Installation ==
  +
=== Debian ===
  +
[[Install TinyOS 2.1 in Debian (lenny)]]
  +
  +
== VMWare ==
  +
login to the set up computer
  +
user: wsn
  +
password: tinyos
  +
  +
start Xubuntos in VMWare-Player
  +
user: xubuntos
  +
password: tinyos
  +
  +
== Test ==
  +
Note: the motelist command does not show any connected motes (I think it is because of that the hardware is very new and therefore cannot be recognised)
  +
  +
To find out which usb device to use, just connect the node and use the ''dmesg'' command.
  +
  +
Transfer test application Blink to the node attached via USB
  +
cd /opt/tinyos-2.1.0/apps/Blink
  +
make iris install.1 mib520,/dev/ttyUSB0
  +
  +
[[File:Tinyos_first_test.JPG]]
  +
  +
  +
== Manuals (CD KIT) ==
  +
  +
[[File:SensorKit.jpg|600px|left|Sensor Kit]]
  +
  +
  +
  +
==== CD Documents and Manuals ====
  +
  +
  +
[[Media:MEP_SYS_Users_Manual_7430-0411-02_A.pdf]]
  +
  +
[[Media:MoteConfig_Users_Manual_7430-0112-01_A.pdf]]
  +
  +
[[Media:MoteView_Users_Manual_7430-0008-05_A.pdf‎]]
  +
  +
[[Media:MoteWorks_Getting_Started_Guide_7430-0102-01_D.pdf]]
  +
  +
[[Media:MPR-MIB_Series_Users_Manual_7430-0021-08_A.pdf‎]]
  +
  +
[[Media:MTS-MDA_Series_Users_Manual_7430-0020-05_A.pdf‎]]
  +
  +
[[Media:TinyOS-nesC_Reference_Manual.pdf‎]]
  +
  +
[[Media:WSN_Quick_Start_Guide.pdf‎]]
  +
  +
[[Media:XMesh_Users_Manual_7430-0108-01_C.pdf]]
  +
  +
[[Media:XServe_Users_Manual_7430-0111-01_D.pdf‎]]
  +
  +
  +
  +
  +
  +
  +
== Room 1.102 ==
  +
=== Hardware ===
  +
* ...
  +
  +
=== Storage ===
  +
We have:
  +
==== a user named <code>sensorlab</code> ====
  +
sensorlab@login:~$ id
  +
uid=13433(sensorlab) gid=913(tmg) groups=913(tmg),6172(senslab),1093888628(AfsPag-336a74)
  +
  +
==== a ''group'' named <code>senslab</code> ====
  +
dn: cn=senslab,ou=groups,dc=informatik,dc=uni-goettingen,dc=de
  +
...
  +
memberUid: sensorlab
  +
memberUid: ashah
  +
memberUid: oalfandi
  +
memberUid: brosenne
  +
memberUid: kellner
  +
  +
This list may get extended with userids of students on request...
  +
  +
==== the user has a home directory ~sensorlab ====
  +
sensorlab@login:~$ pwd
  +
/afs/informatik.uni-goettingen.de/user/s/sensorlab
  +
  +
==== obligatory home page ====
  +
http://user.informatik.uni-goettingen.de/~sensorlab/
  +
  +
The account "sensorlab" should '''not''' be used by any member of the group "senslab". Instead use your own account - that's what group membership is for!
  +
  +
== See also ==
  +
* [[SL:tmg94]] -- ESXi Server for hosting Virtual Machines
  +
* [[SL:Virtual Machines]]
  +
* [[SL:Remote Access]] -- reach in from the outside world
  +
* [[SL:Topology]] -- the network address ranges, machine names...
  +
  +
[[Category:Sensorlab]]

Version vom 23. Oktober 2012, 08:53 Uhr


Nodes Hardware

The sensor nodes we have ordered are from Crossbow technology (http://www.xbow.com/Products/productdetails.aspx?sid=264) Basically, the sensors operate in 2.4GHz ISM band. The range of the radio module is about up to 50 m indoor and up to 300 m outdoor.

For more details see the data sheet: http://www.xbow.com/Products/Product_pdf_files/Wireless_pdf/IRIS_Datasheet.pdf

Sensor board: MTS400 including the following sensors

  • Dual-axis Accelerometer: Analog Devices ADXL202JE
  • Barometric Pressure Sensor: Intersema MS5534AM
  • Ambient Light Sensor: TAOS TSL2550D
  • Relative Humidity & Temperature Sensor: Sensirion SHT11

Documents

TinyOS

General documents can be found on http://docs.tinyos.net/index.php/Main_Page

TinyOS Iris API: http://www.tinyos.net/tinyos-2.1.0/doc/nesdoc/iris/

How To

How To Disassemble a Sensor Node to Reprogram it (.pdf) (.doc)

Modifications for iris motes

PacketParrot application

The PacketParrot application which is provided with TinyOS does not work on directly on the Iris motes. Thus, the following modified version can be used instead. The modifications are basically replacing the special radio component, which is used for sending and receiving, by the generic AMSenderC and AMReceiverC components.

PacketParrotC.nc

PacketParrotP.nc

Installation

Debian

Install TinyOS 2.1 in Debian (lenny)

VMWare

login to the set up computer 

 user: wsn
 password: tinyos

start Xubuntos in VMWare-Player 

 user: xubuntos
 password: tinyos

Test

Note: the motelist command does not show any connected motes (I think it is because of that the hardware is very new and therefore cannot be recognised)

To find out which usb device to use, just connect the node and use the dmesg command.

Transfer test application Blink to the node attached via USB 

 cd /opt/tinyos-2.1.0/apps/Blink
 make iris install.1 mib520,/dev/ttyUSB0

Tinyos first test.JPG


Manuals (CD KIT)

Sensor Kit


CD Documents and Manuals

Media:MEP_SYS_Users_Manual_7430-0411-02_A.pdf

Media:MoteConfig_Users_Manual_7430-0112-01_A.pdf

Media:MoteView_Users_Manual_7430-0008-05_A.pdf‎

Media:MoteWorks_Getting_Started_Guide_7430-0102-01_D.pdf

Media:MPR-MIB_Series_Users_Manual_7430-0021-08_A.pdf‎

Media:MTS-MDA_Series_Users_Manual_7430-0020-05_A.pdf‎

Media:TinyOS-nesC_Reference_Manual.pdf‎

Media:WSN_Quick_Start_Guide.pdf‎

Media:XMesh_Users_Manual_7430-0108-01_C.pdf

Media:XServe_Users_Manual_7430-0111-01_D.pdf‎




Room 1.102

Hardware

* ...

Storage

We have:

a user named sensorlab

sensorlab@login:~$ id
uid=13433(sensorlab) gid=913(tmg) groups=913(tmg),6172(senslab),1093888628(AfsPag-336a74)

a group named senslab

dn: cn=senslab,ou=groups,dc=informatik,dc=uni-goettingen,dc=de
...
memberUid: sensorlab
memberUid: ashah
memberUid: oalfandi
memberUid: brosenne
memberUid: kellner

This list may get extended with userids of students on request...

the user has a home directory ~sensorlab

sensorlab@login:~$ pwd
/afs/informatik.uni-goettingen.de/user/s/sensorlab

obligatory home page

http://user.informatik.uni-goettingen.de/~sensorlab/

The account "sensorlab" should not be used by any member of the group "senslab". Instead use your own account - that's what group membership is for!

See also

Abgerufen von „https://doc.informatik.uni-goettingen.de/wiki/index.php?title=SL:Introduction&oldid=481“